如何有效處理鋁合金外殼?鋁合金外殼不銹鋼之間有很大的區別，鋁合金外殼易變形，不銹鋼則不易變形。鋁合金外殼一般都是用于裝飾，而且重量較輕，這就是它的優勢所在。鋁合金外殼的缺點是它容易變形，所以在使用過程中，必須小心謹慎。

　　下面介紹一下如何有效處理鋁合金外殼:

　　1、在使用鋁合金外殼前，應先用油擦拭干凈外殼表面，以免銹蝕。

　　2、油漆的顏色較淺，應選擇深色油漆。

　　3、使用前應檢查外殼表面是否有油漆脫落等缺陷，如有脫落，應先用油漆刷補上。

　　4、外殼表面如果銹蝕，可用擦鋁粉或磨料擦干凈。

　　5、為了延長鋁合金外殼的使用壽命，建議在易腐蝕的部位做一些保護處理，如噴漆、涂膜等。

　　以上就是關于如何有效處理鋁合金外殼的介紹，希望能幫助到大家。

　　現在，鋁合金手機殼占據手機市場份額越來越大，手機廠商也越來越重視鋁合金手機殼的設計和制造。鋁合金殼材料輕、硬度高，防水防塵性能好，耐磨損性能也很強，目前越來越多的手機廠商開始使用鋁合金殼材料。

　　但是，鋁合金材料的加工難度較大，殼體表面易起氧化皮、容易生銹，不容易打磨平整。

　　所以，如果想要制作出好的鋁合金手機殼，需要注意以下幾點：

　　1、采用高品質的鋁合金材料。目前市面上使用的鋁合金材料大多都是6063鋁合金，這種材料雖然質地輕，但是硬度較低，不能滿足手機殼的要求。而且6063鋁合金在加工過程中容易出現氧化皮，所以需要選擇一種更加優質的鋁合金材料。

　　2、制作工藝要精良。鋁合金材料的加工過程比較復雜，所以制作工藝要精良，經過多道工序才能保證手機殼的質量。

　　3、表面處理要到位。如果鋁合金材料的表面處理不到位，易起氧化皮，所以制作工藝要精良，經過多道工序才能保證手機殼的質量。

　　4、打磨平整。表面如果不平整，會影響手機殼的外觀，所以需要進行打磨平整。

　　鋁合金手機殼具有輕、硬度高、防水防塵、耐磨損等優點，目前越來越多的手機廠商開始使用鋁合金殼材料。但是，鋁合金材料的加工難度較大，所以制作工藝要精良，經過多道工序才能保證手機殼的質量。

　　Nowadays, aluminum alloy mobile phone shell occupies an increasing market share, and mobile phone manufacturers are paying more and more attention to the design and manufacturing of aluminum alloy mobile phone shell. Aluminum alloy shell is light, has high hardness, good waterproof and dustproof performance, and strong wear resistance. At present, more and more mobile phone manufacturers begin to use aluminum alloy shell.

　　However, the processing difficulty of aluminum alloy is large, and the surface of shell is easy to oxide, rust and not easy to be polished and flat.

　　Therefore, if you want to make a good aluminum alloy mobile phone shell, you need to pay attention to the following points:

　　1. Use high-quality aluminum alloy materials. Most of the aluminum alloys used on the market are 6063 aluminum alloys, which are light in texture but have low hardness and cannot meet the requirements of mobile phone shell. Moreover, it is easy to oxide the surface during the processing of 6063 aluminum alloy, so a more quality aluminum alloy material is needed.

　　2. The manufacturing process should be fine. The processing of aluminum alloy is more complicated, so the manufacturing process should be fine, and the quality of mobile phone shell can only be guaranteed through many processes.

　　3. The surface treatment should be in place. If the surface treatment of aluminum alloy material is not in place, it is easy to oxide, so the manufacturing process should be fine and the quality of mobile phone shell can only be guaranteed through many processes.

　　4. Polishing flat. If the surface is not flat, it will affect the appearance of mobile phone shell, so it needs to be polished and flat.

　　Aluminum alloy mobile phone shell has the advantages of light weight, high hardness, waterproof, dustproof and wear resistance. At present, more and more mobile phone manufacturers begin to use aluminum alloy shell material. However, the processing difficulty of aluminum alloy is large, so the manufacturing process should be fine and the quality of mobile phone shell can only be guaranteed through many processes.